■ IR resistance test range: 10kΩ - 50TΩ
■ Charge current: 2mA , 25mA, 200mA
■ Test speed: 50ms
■ Accuracy: ±2% (< 1TΩ )
■ Test voltage range: 10-500V, 1V step
■ 320×240 dot-matrix LCD
■ Ultra-low leakage current test: minimum current is
10pA, accuracy: 2% ±2pA
■ Dual outputs (precharge voltage output and test
voltage output) can be set.
■ The precharge voltage output can be set to follow the test
voltage output and can be finely adjusted on test voltage.
Also the precharge voltage can be set to work in
independent mode.
■ 100W powerful charging function
■ Contact detection function for capacitive components
■ When the test current is less than 10nA, the internal input
impedance can be selected between 10kΩ and 1MΩ to
ensure rapid and accurate test.
■ 7 current ranges, manual or auto range mode
■ 4-bin comparison function
■ Programmable sequence test mode
■ R-T and I-T Curve test and display mode
■ Screen hardcopy to be saved as BMP file to a U disk
■ Automatically upgrade firmware by a U disk
■ Achieve automatic test system by Handler interface
■ Achieve remote control by RS232C and USB
Device interface
■ Support scanning interface for mass tests
■ Auto store setup parameters
■ Selectable Chinese and English operation interfaces
- Brief Introduction
■ TH2684/TH2684A High Precision IR Tester is an intelligent measurement instrument that is used for rapid measurements on IR properties of electronic parts and components, dielectric materials, equipments, cables, etc. Large LCD and user friendly menu provide you easier operation.
This instrument is especially designed for capacitor IR test TH2684/TH2684A can achieve rapid measurements through following methods:
1. Selectable internal input impedance: If the current is greater than 10nA, only 10kΩ input impedance can be used; if the current is below 10nA, you can choose 10kΩ or 1MΩ impedance to test.
2. With the built-in dual voltage output, TH2684 can charge large capacitors. By dual voltage output, TH2684 is able to output a precharge voltage up to 500V, 200mA. In voltage follow mode, precharge voltage follow with the test voltage output and can be finely adjusted. Above features ensure the perfect charge of capacitive materials.
3. TH2684A can output a voltage of 1000V, 100mA to fully charge the capacitive material. In addition, user can program the sequence measurement steps (up to 18 steps) on TH2684/TH2684A. For instance, charge, wait, test, and discharge steps can be programmed. Each step can last up to 100s.
TH2684/TH2684A has a unique contact detection function. For capacitive material such as capacitors and cables, contact detection function can detect the contact of components under test. Moreover, this detection function will not increase any test time.
TH2684 equips with interfaces of RS232, USB DEVICE, SCANNING and Handler. Handler interface provide convenience for automatic test system; SCANNING interface is useful for mass measurement of components. User can use a scanner to speed measurement of components.
- Application
- Technical Parameter
Model TH2684 TH2684A Resistance Test Range kΩ to 50TΩ kΩ to 100TΩ Accuracy Test current > 100pA: 2%Test current ≤ 100 pA: 2% ± Vtest/2pA Current Test Range Range 1 :100uA – 1mA , Internal Input impedance 10 kΩ Range 2 :10uA – 100uA , Internal Input impedance 10 kΩ Range 3 :1uA – 10uA , Internal Input impedance 10 kΩ Range 4 :100nA – 1uA , Internal Input impedance 10 kΩ Range 5 :10nA – 100nA, Internal Input impedance 10 kΩ Range 6 :1nA – 10nA, Internal Input impedance 10 kΩ or 1MΩ (selectable) Range 7 :10pA – 1nA, Internal Input impedance 10 kΩ or 1MΩ (selectable) Accuracy 2% ± 2pA Measurement Voltage Range 10 to 500V, 1V resolution to 1000V,1V resolution Accuracy 2% of readout,or ± 1V Source Resistance 200Ω Current Limit 2,25,or 200mA 2, 25 , or 100mA Voltage Output Manually turn on or off on front panel, or controlled by built-in timer, or by remote control. Timing Programmable charge time: 0 to 1000s Measurement Delay 0 to 1000s programmable Discharge Resistance 2kΩ Discharge Time t = 0.03 x Cx (in μF), when Vtest falls to 1% of the test level. Measurement Speed Trig Mode Single measurement: < 100ms(exclude charge time)Average up to 100 measurements:<100+ (N-1) x 100 ms (exclude charge) Continuous Mode Direct readout: 100ms – 10000ms depending on average number Comparator bins:(3 bins for PASS,1 bin for FAIL) Range Mode Auto, Hold Average Times to100 Memory Sets of setup values can be stored. Standard Interface GPIB (optional), RS232C, HANDLER interface output, USBDEVICE ( USBTMC and USBCDC support), USBHOST, SCANNING Operating Temperature and Humidity 10°C - 40°C, ≤90%RH Power Supply to 130 V AC(60Hz) orto 260V AC(50HZ) Power Consumption TH2684 : 250WTH2684A: 150W Dimensions (W×H×D) 430mm×400mm×130mm Weight TH2684 : 14kgTH2684A: 10kg
- Accessary
| Standard | |||||
| Accessories name | Model | ||||
| Test line at both ends | TH26004B | ||||
| Optional | |||||
| Accessories name | Model | ||||